I’ve always done protein powder first, then add liquid and doing it the other way around sounds like blasphemy.
Never get any clumps either!
Dry powder on top of a liquid is pure insanity, next you’ll tell me you add the milk into a bowl of cereal before the cereal
But from there, there is actually much debate about which order of combining is best. Some say that adding dry into wet leads to clumps of dry ingredients floating in the batter, while others say that actually the opposite, adding wet to dry, leads to, well, clumps.
It would appear that the jury is still out, and everyone despises clumps. But one thing is definitely true: It’s much harder to successfully add dry ingredients into wet ingredients neatly. That order tends to lead to a giant puff of flour wafting toward the ceiling, and settling all over the counters, while a steady, viscous stream of wet ingredients will instead narrowly ribbon its way down into the bowl containing dry ingredients, and nowhere else.
The powder flying every where is something to take into consideration, i use a fork, start slow then fast once powder is fully submerged. In termsof clumps they all eventually soak through and dissolve if you let it sit.
Never used it so not sure, maybe try a couple experiments. At least with protein when you try to make a paste it becomes a thick hard goop that is difficult to stir, and when you diluted it doesn’t go into solution any faster than if it was dry. And the reason I say put it on top of the liquid is because when it’s in the bottom it still goods up, sticks to the cup and doesn’t mix. But if it’s on top it stays suspended allowing it to mix when you stir
The best method (including Soylent) is adding 2.5-4cm (1"1.5") of water to the shaker bottle, adding the powder, tapping the bottle on the counter a couple times, then topping off with water. Once filled, replace the top, give it a good shake, let it sit for a minute or two, and then give it a final shake to get the last bit off the side.
This method prevents the powder from sticking to the inside edge around the base or to the top and reduces the shaking needed. If you’re really hungry, with Soylent, you can actually use up to 105g (3.5 scoops) of powder in the standard sized shaker bottle and it will still mix properly if you finish adding water after replacing the top to a little below the flip-cap opening.
You can do the protein powder first. Just make sure that when you pour in the water, it stays on top of the protein and doesn’t seep through to the bottom. Then flip the bottle over, shake it (without flipping) until all the powder unsticks from the bottom, then proceed to shake normally.
Alternatively, fill the bottle with about an inch of water, add the powder, then fill the rest of the way with water and shake normally.
The problem with water first is that you can’t stick the scoop into the bottle and protein powder flies off everywhere.
With the exception of protein powder, add it on top of the liquid and mix it.
Yeah that’s what I do. Simple easy and no clumps.
I’ve always done protein powder first, then add liquid and doing it the other way around sounds like blasphemy.
Never get any clumps either!
Dry powder on top of a liquid is pure insanity, next you’ll tell me you add the milk into a bowl of cereal before the cereal
But from there, there is actually much debate about which order of combining is best. Some say that adding dry into wet leads to clumps of dry ingredients floating in the batter, while others say that actually the opposite, adding wet to dry, leads to, well, clumps.
It would appear that the jury is still out, and everyone despises clumps. But one thing is definitely true: It’s much harder to successfully add dry ingredients into wet ingredients neatly. That order tends to lead to a giant puff of flour wafting toward the ceiling, and settling all over the counters, while a steady, viscous stream of wet ingredients will instead narrowly ribbon its way down into the bowl containing dry ingredients, and nowhere else.
The powder flying every where is something to take into consideration, i use a fork, start slow then fast once powder is fully submerged. In termsof clumps they all eventually soak through and dissolve if you let it sit.
Would that also be true of something like Soylent?
Never used it so not sure, maybe try a couple experiments. At least with protein when you try to make a paste it becomes a thick hard goop that is difficult to stir, and when you diluted it doesn’t go into solution any faster than if it was dry. And the reason I say put it on top of the liquid is because when it’s in the bottom it still goods up, sticks to the cup and doesn’t mix. But if it’s on top it stays suspended allowing it to mix when you stir
Soylent if you have one of those shakers should be good enough as is.
The best method (including Soylent) is adding 2.5-4cm (1"1.5") of water to the shaker bottle, adding the powder, tapping the bottle on the counter a couple times, then topping off with water. Once filled, replace the top, give it a good shake, let it sit for a minute or two, and then give it a final shake to get the last bit off the side.
This method prevents the powder from sticking to the inside edge around the base or to the top and reduces the shaking needed. If you’re really hungry, with Soylent, you can actually use up to 105g (3.5 scoops) of powder in the standard sized shaker bottle and it will still mix properly if you finish adding water after replacing the top to a little below the flip-cap opening.
You can do the protein powder first. Just make sure that when you pour in the water, it stays on top of the protein and doesn’t seep through to the bottom. Then flip the bottle over, shake it (without flipping) until all the powder unsticks from the bottom, then proceed to shake normally.
Alternatively, fill the bottle with about an inch of water, add the powder, then fill the rest of the way with water and shake normally.
The problem with water first is that you can’t stick the scoop into the bottle and protein powder flies off everywhere.
I use a mug,but I see how that an work